The Kit Cars Forum Visit our friends!
Kit Cars Links
January 08, 2009, 10:15:35 PM *
Welcome, Guest. Please login or register.
Did you miss your activation email?

Login with username, password and session length
News: No News is good news!
 
   Home   Help Search Login Register  
The Kit Cars Forum > Kitcar Discussion Forums > Technical Discussion & Question (Moderators: AdminAri, FunnyWheels) > Preventing paint damage from mold making?
Pages: [1]
« previous next »
  Print  
Author Topic: Preventing paint damage from mold making?  (Read 615 times)
G-Nasty
Newbie
*
Offline Offline

Posts: 11


Stop Inbreeding-Ban Country Music


View Profile WWW
« on: October 07, 2002, 07:00:37 PM »
What have you used that has proven results? I dont want to trash the paint when I pull the molds from the panels-what products are the best? I will be making epoxy molds. How should I prep the paint so it is not damaged? Any tips greatly appreciated-
OUT>
« Last Edit: December 31, 1969, 05:00:00 PM by 1043298000 » Logged
G-Nasty
Newbie
*
Offline Offline

Posts: 11


Stop Inbreeding-Ban Country Music


View Profile WWW
« Reply #1 on: October 08, 2002, 05:22:08 PM »
I take it that paint damage will have to occur- no matter what I use (wax PVA etc. etc.) I was wanting to paint the car anthracite. Maybe I will have an excuse to after these molds are made.
I'll post some pics on damage.
OUT>
« Last Edit: December 31, 1969, 05:00:00 PM by 1043298000 » Logged
The Kit Cars Forum
« Reply #1 on: October 08, 2002, 05:22:08 PM »
 Logged
beerman
Full Member
***
Offline Offline

Posts: 121


I love YaBB 1G - SP1!


View Profile
« Reply #2 on: October 08, 2002, 05:52:21 PM »

I think the best choice is to call a expert fiberglass shop for this answer.There is a good chance that if you wax and apply a good pva to the part it might be ok, but to be on the safe side i would ask again an expert that has done this before. If you plan to repaint the parts anyway then , i guess you will have to decide. I hope you luck, and please let us know how it turns out.You could e-mail this guy , maybe he can help you.http://www.hotrodder.com/32Blowpar/page10.html
Logged
VRESpeedFreak
Newbie
*
Offline Offline

Posts: 32


F-40 Lover


View Profile
« Reply #3 on: October 09, 2002, 07:30:50 PM »
Just out of curiousity...unless I missed something Smiley

But, what are you making molds of?
« Last Edit: December 31, 1969, 05:00:00 PM by 1043298000 » Logged
GodAlex
Jr. Member
**
Offline Offline

Posts: 85


I Feel the Need:  The Need for Speed


View Profile
« Reply #4 on: October 09, 2002, 08:47:58 PM »
several coats of wax and several layers of PVA usually work.  I know a guy who made a kit long time ago (he taught at a technical college in Fla).  He recommended up to 7 coats of PVA.  According to him it would separate with out damaging the original.  I wish I knew where the directions were, because I wrote it all down when talking with him about it.
« Last Edit: December 31, 1969, 05:00:00 PM by 1043298000 » Logged
Amida
Patron Class Member
Hero Member
*****
Offline Offline

Posts: 747


vote for a better spyder


View Profile
« Reply #5 on: October 10, 2002, 04:49:50 AM »
Minimizing the heat build-up of the resin is key.  Do not lay down more than 2 layers of mat at a time.  Adjust amount of catalyst to provide a slower curing rate to prevent too much heat build-up.  If the paint is fully cured, several coats of mold release wax and PVA should do the trick.  
« Last Edit: December 31, 1969, 05:00:00 PM by 1043298000 » Logged
Tat2_Keith
Newbie
*
Offline Offline

Posts: 14


I love YaBB 1G - SP1!


View Profile
« Reply #6 on: October 10, 2002, 03:22:48 PM »
The best way to avoid damage is to use 1/2% hardner and a polyester tooling resin with atleast 3 coats of tooling gelcoat.As for ensuring a safe release, wax 6 times with Partall#2 release wax and the heavier purple PVA.
« Last Edit: December 31, 1969, 05:00:00 PM by 1043298000 » Logged
G-Nasty
Newbie
*
Offline Offline

Posts: 11


Stop Inbreeding-Ban Country Music


View Profile WWW
« Reply #7 on: October 14, 2002, 03:53:56 PM »
Thanks for the technical help & replies-
OUT>
Logged
The Kit Cars Forum
   
 Logged
Pages: [1]
  Print  
« previous next »
 
Jump to:  

Powered by SMF 1.1.5 | SMF © 2006-2008, Simple Machines LLC | Sitemap | Terms of Use | Privacy Policy
All trademarks and copyrights on this page are owned by their respective owners. Comments are owned by the Poster.